TAMREX X-Air Cup FFP2V filtering half mask with exhalation valve
- FFP2 protection class: 94% filtration efficiency
- With exhalation valve
- Moulded construction
- Adjustable nose clip, two headbands
- Protection against solid particles and aerosols
- For single use for up to 8 hours
TAMREX X-Air Cup FFP2V is a moulded FFP2-class filtering half mask with an exhalation valve that protects your respiratory tract against airborne solid particles and water- and liquid-based aerosols. The moulded design, adjustable nose clip and two headbands allow you to achieve a secure fit on your face. The exhalation valve helps reduce heat and moisture build-up inside the mask, making it more comfortable to wear.
FFP2 protection class – at least 94% filtration efficiency
The filtering half mask complies with European standard EN 149:2001+A1:2009 and belongs to protection class FFP2 NR.
FFP2-class filter material has an efficiency of at least 94%, meaning that no more than 6% of test particles pass through the filter material under the test conditions specified in the standard.
Filtration efficiency has been tested using sodium chloride (NaCl) and paraffin oil aerosols at an airflow of 95 l/min. Breathing resistance is up to 24 mm H₂O.
The filtering half mask has an assigned protection factor (APF) of 10.
Exhalation valve reduces heat and moisture build-up
The filtering half mask is equipped with an exhalation valve that helps reduce the build-up of heat and moisture from exhaled air inside the mask. This makes the filtering half mask more comfortable to wear, particularly during prolonged use.
The exhalation valve does not filter exhaled air. This filtering half mask is therefore not suitable for situations where you need to protect other people or maintain a sterile environment.
Moulded design
The filtering half mask has a moulded, cup-shaped design that gives it a defined three-dimensional shape.
The filtering half mask is individually packaged in plastic wrapping, which you should open immediately before use. Before fitting the mask, check its condition and expiry date.
Adjustable nose clip and two headbands
To fit the filtering half mask, place it under your chin and over your nose. Position the upper headband high on the back of your head and the lower headband below your ears. The headbands must lie flat, without twists.
Use both hands to mould the nose clip to the shape of your face for the closest possible fit.
Always check the seal of the filtering half mask before entering a contaminated environment. If you cannot eliminate air leakage between the mask and your face, you must not use the filtering half mask. A beard, moustache or the shape of your face may compromise the seal and reduce the level of protection.
Protection against solid particles and aerosols
The filtering half mask is designed to protect your respiratory tract against solid particles and water- and liquid-based aerosols.
The filtering half mask does not protect against gases or vapours. You must also not use it in environments where the oxygen content is below 19.5%, there is a risk of explosion, the composition and concentration of contaminants are unknown, or the contamination poses an immediate threat to life.
You must select suitable respiratory protective equipment based on a workplace risk assessment. You must have received the necessary training.
Single use for up to 8 hours
The NR (Non-Reusable) marking means that the filtering half mask is intended for single use during one work shift, for a maximum of 8 hours.
You must wear the filtering half mask throughout your time in a contaminated environment. Replace the mask if it is damaged, dirty or damp, or if breathing becomes more difficult. You must also replace the mask after removing it in a contaminated environment.
You must not wash or reuse the filtering half mask.
If you experience an allergic reaction, leave the hazardous area, remove the filtering half mask and seek medical advice.
Details
You must store the filtering half mask in its original packaging, protected from direct sunlight, solvents, freezing and mechanical damage. You must follow the temperature and humidity requirements stated on the packaging.
Shelf life: 5 years from the date of manufacture
- EN 149:2001+A1:2009
- PPE Cat III
- (EL) 2016/425
- CE 2797